Does the Darkvoice 336SE drive the Drop + Sennheiser HD 6XX?

Computed from rated specifications · target SPL 110 dB · load 300 Ω

Ample OTL-compatible pairing

The Darkvoice Darkvoice 336SE drives the Drop + Sennheiser HD 6XX with ample headroom (~11.7 dB headroom at 300 ohms; needs ~16.7 mW, delivers 250 mW). This OTL tube amp suits the headphone's impedance (300 Ω) — a classically compatible pairing for high-output-impedance tube sources.

Headroom
11.7 dB
Required (110 dB SPL)
16.7 mW
Delivered (@ 300 Ω)
250 mW
Required voltage
2.24 Vrms

Power Headroom

Headroom: 11.7 dB 0 · target 11.7 dB below target marginal adequate ample -14 dB +10 +20 +36 dB

Scale shows dB headroom above the 16.7 mW required to reach 110 dB SPL. Amp delivers 250 mW at 300 Ω (+11.7 dB above target).

Drop + Sennheiser HD 6XX Dynamic · over-ear
Impedance 300.0 Ω rated
Sensitivity 97.77 dB/mW rated
Driver Dynamic
Spec basis Rated low confidence
Electrically equivalent to Sennheiser HD 650 (same driver assembly). Rated specs derived from HD 650 manufacturer documentation. No RAA measurement page for this Drop collab. · Source ↗
Darkvoice 336SE Desktop Tube · Single Ended
Output impedance assumed 100.0 Ω estimated
Power @ 300 Ω 250 mW
Power @ 600 Ω 125 mW *est.
Power source Estimated low confidence
* Loads marked "est." are derived from the published voltage ceiling at a lower-impedance load (V = √(P·R) → P_higher = V²/R_higher). All derivations are upward only.
OTL tube amp using 6N5P output tubes. Manufacturer page (Apos, analogmetric) states only 'Power handling capacity: 1 W' with no load specification. Power figure of 250 mW @ 300 Ω is a conservative estimate based on OTL topology similar to the Bottlehead Crack; treat as approximate. Output impedance of 100 Ω is estimated from OTL/6N5P tube topology — manufacturer does not publish this figure. 600 Ω derived from 300 Ω. · Source ↗
Impedance compatibility

This OTL tube amp's high output impedance (100 Ω) is a good match for the Drop + Sennheiser HD 6XX's 300 Ω impedance. The impedance ratio (3.0×) falls within the recommended range for high-output-impedance tube sources — a classically well-matched pairing.

Specification confidence: low

One or more amp specifications (power output or output impedance) are estimated rather than published by the manufacturer. Treat this pairing's verdict as approximate.

Headphone specification confidence: low

The headphone's rated specifications are from estimated or secondary sources. Measured figures (where present) are more reliable.

Where to buy

Darkvoice 336SE on Amazon ↗ Drop + Sennheiser HD 6XX on Amazon ↗

Disclosure: links above are Amazon affiliate links. As an Amazon Associate this site earns from qualifying purchases — at no extra cost to you. Affiliate commissions do not influence verdicts; all analysis is computed independently from the data.

AmplifierHeadroom
Schiit Lyr 3 Ample 17.3 dB
Schiit Valhalla 2 Ample 16.8 dB
JDS Labs Atom Amp 2 Ample 12.3 dB
Topping L30 Ample 12.2 dB
iFi Zen DAC V2 Adequate 3.3 dB
Apple USB-C to 3.5mm Insufficient -7.0 dB

See all amplifiers for the Drop + Sennheiser HD 6XX →

HeadphoneHeadroom
Koss Porta Pro Ample 19.6 dB
Grado SR80x Ample 19.3 dB
Audio-Technica ATH-AD700X Ample 14.0 dB
Focal Clear (original) Ample 14.0 dB
AKG K240 Studio Adequate 5.0 dB
Fostex T50RP Mk3 Adequate 3.1 dB

See all headphones for the Darkvoice 336SE →