Does the Darkvoice 336SE drive the Beyerdynamic DT 770 Pro 80?

Computed from measured specifications · target SPL 110 dB · load 300 Ω

Ample

The Darkvoice Darkvoice 336SE drives the Beyerdynamic DT 770 Pro 80 with ample headroom (~10.2 dB headroom at 300 ohms; needs ~24.0 mW, delivers 250 mW). Note: this OTL tube amp's high output impedance (100 Ω) interacts strongly with this low-impedance (93 Ω) headphone, which can audibly alter its tonal balance. OTL tube amps are best paired with high-impedance (250 Ω+) headphones; this is a less ideal match.

Headroom
10.2 dB
Required (110 dB SPL)
24.0 mW
Delivered (@ 300 Ω)
250 mW
Required voltage
1.50 Vrms

Power Headroom

Headroom: 10.2 dB 0 · target 10.2 dB below target marginal adequate ample -14 dB +10 +20 +36 dB

Scale shows dB headroom above the 24.0 mW required to reach 110 dB SPL. Amp delivers 250 mW at 300 Ω (+10.2 dB above target).

Beyerdynamic DT 770 Pro 80 Dynamic · over-ear
Impedance (rated) 80 Ω
Impedance (measured) Source: reference-audio-analyzer.pro/en/r… 93.4 Ω measured
Sensitivity 96.2 dB/mW measured
Driver Dynamic
Spec basis Measured
Measured by Reference Audio Analyzer (https://reference-audio-analyzer.pro/en/report/hp/beyerdynamic-dt-770-pro-80.php) · Source ↗
Darkvoice 336SE Desktop Tube · Single Ended
Output impedance assumed 100.0 Ω estimated
Power @ 300 Ω 250 mW
Power @ 600 Ω 125 mW *est.
Power source Estimated low confidence
* Loads marked "est." are derived from the published voltage ceiling at a lower-impedance load (V = √(P·R) → P_higher = V²/R_higher). All derivations are upward only.
OTL tube amp using 6N5P output tubes. Manufacturer page (Apos, analogmetric) states only 'Power handling capacity: 1 W' with no load specification. Power figure of 250 mW @ 300 Ω is a conservative estimate based on OTL topology similar to the Bottlehead Crack; treat as approximate. Output impedance of 100 Ω is estimated from OTL/6N5P tube topology — manufacturer does not publish this figure. 600 Ω derived from 300 Ω. · Source ↗
Impedance caution

This OTL tube amp's output impedance (100 Ω) is high relative to this headphone's 93 Ω impedance (ratio 0.9×). OTL tube amps are best paired with headphones ≥ 250 Ω; this combination may cause audible tonal coloration.

Specification confidence: low

One or more amp specifications (power output or output impedance) are estimated rather than published by the manufacturer. Treat this pairing's verdict as approximate.

Where to buy

Darkvoice 336SE on Amazon ↗ Beyerdynamic DT 770 Pro 80 on Amazon ↗

Disclosure: links above are Amazon affiliate links. As an Amazon Associate this site earns from qualifying purchases — at no extra cost to you. Affiliate commissions do not influence verdicts; all analysis is computed independently from the data.

AmplifierHeadroom
Schiit Lyr 3 Ample 24.0 dB
Schiit Asgard 3 Ample 20.2 dB
Schiit Magni Heretic Ample 18.2 dB
FiiO K7 Ample 17.1 dB
Schiit Fulla 4 Adequate 8.0 dB
Apple USB-C to 3.5mm Marginal 1.1 dB

See all amplifiers for the Beyerdynamic DT 770 Pro 80 →

HeadphoneHeadroom
Koss Porta Pro Ample 19.6 dB
Grado SR80x Ample 19.3 dB
Audio-Technica ATH-AD700X Ample 14.0 dB
Focal Clear (original) Ample 14.0 dB
AKG K240 Studio Adequate 5.0 dB
Fostex T50RP Mk3 Adequate 3.1 dB

See all headphones for the Darkvoice 336SE →